Acnodes FPC 5105 Manual do Utilizador

FPC 5105 Industrial Fanless Panel PC © Copyright 2013 Acnodes, Inc. All rights reserved. Product description and product specifications are su

1.4 I/O Outlets Please refer to the following illustration for I/O locations of the FPC5105.

1.5 Packing List When you receive the FPC5105, the bundled package should contain the following items:  FPC5105 x 1  Panel Mount Kit x 6 

CHAPTER 2 HARDWARE INSTAL LATION The FPC5105 provides rich I/O ports and flexible expansions for you to m eet different demand. The ch

Pin Signal Pin Signal 1 Data Carrier Detect (DCD) 6 Data Set Ready (DSR) 2 Receive Data (RXD) 7 Request To Send (RTS) 3 Transmit Dat

Pin RS-232 RS-422 RS-485 1 DCD TX- Data- 2 RXD TX+ Data+ 3 TXD RX+ N.C 4 DTR RX- N.C. 5 GND No use No use 6 DSR No use No use 7 RTS No use No use

2.3 Ethernet The FPC5105 is equipped with two high performance Plug and Play Ethernet interfaces, full compliant with IEEE 802.3 standard, and ca

2.4 Mountings – Panel/Wall/Desktop/VESA There are several mounting ways for the FPC5105, Panel, Wall, Desktop and VESA mountings.

2.4.2 Wall-M ounting The FPC5105 is designed for Wall m ounting application. Please refer to the following steps: Find out the screws as ma

Step 2 Assem ble the desktop stand to the chassis, and fix the screws.

2.4.4 VESA-ARM Mounting Step 1 Find out the screws as marked on the back side of chassis. Step 2 Assem ble the VESA-A

FPC 5105 Industrial Fanless Panel PC Disclaimers This manual has been carefully checked and believed to contain accurate in

Step 3 VESA m ounting Installation completed. Caution Use recommended/suitable mounting apparatus to avoid risk of injury.

2.5 HDD Installation The FPC5105 provides a convenient Hard Disk Drive (HDD) bracket for users to install 2.5” SATA HDD. Please follow the step

3. Screw the 2.5” HDD, together with the HDD Mylar, to the HDD bracket. 4. Fix the HDD brack et into the system , and plug the data and powe

2.6 DRAM Installation The FPC5105 provides one 204-pin DDR3 800MHz SO-DIMM socket that support sys tem mem ory up to 2GB. Please follow steps

3. Install the memory module into the socket and push it firm ly down until it is fully seated. The socket latches are levered upwards and clippe

2.7 Wireless LAN Card Installation The FPC5105 provides one Mini card slot for user to install one wireless LAN card. When installing the wireles

NOTE: Please have the extented bracket when using half-size mini card.

CHAPTER 3 AMI BIOS SETUP UTILITY This chapter provides users with detailed description how to set up basic system configuration through the A

3.2 Navigation Keys The BIOS setup/utility uses a k ey-based navigation system called hot keys. Most of the BIOS setup utility hot keys

3.3 Main Menu When you first enter the Setup Utility, you will enter the Main setup screen. You can always return to the Main s etup screen by

FPC 5105 Industrial Fanless Panel PC © Copyright 2013 Acnodes, Inc. All rights reserved. Product description and product specifications are su

3.4 Advanced Menu  Launch PXE OpROM Use this item to enable or disable the boot ROM function of the onboard LAN chip when the s

 ACPI Settings You can use this screen to select options for the ACPI Settings, and change the value of the selected option. A descrip

 CPU Configuration This screen shows the CPU Configur ation, and you can change the value of the selected option.

 IDE Configuration  SATA Controller(s) The optional settings are: [Disabled]; [Enabled].  Configure SATA as The optional settings are:

 USB Configuration You can use this screen to select options for the USB Configuration, and change the value of the selected option. A descript

 NCT6627UD Super IO Configuration You can use this screen to select options for the Super IO Configuration, and change the value of the select

 PC Health Status This screen shows the Hardware Health Configuration, and a description of the selected item appears on the right s

3.5 Chipset Menu The Chipset menu allows users to change the advanced chipset settings. You can select any of the items in the left frame of the

 M emory Frequency and Timing This item is for m emory frequency and timing settings. Press <Enter> to go to the sub m enu.

3.6 Boot Menu The Boot m enu allows users to change boot options of the s ystem.  Boot Settings Configuration 

Table of Contents Disclaimers ...

3.7 Security Menu The Security m enu allows users to change the security settings for the s ystem.  Administrator Password This item indica

3.8 Exit Menu The Save & Exit menu allows users to load system configuration with optimal or failsafe default values.  Save Changes and

 Save Changes When you have com pleted the system configuration changes, select this opti on to save changes. Select Save Changes from th

CHAPTER 4 DRIVERS INST ALLATION 4.1 System FPC5105 supports W indows7 32-bit. To facilitate the installation of system driver, please carefu

4.2 Touch Screen The FPC5105 uses the 5-wire analog resistve. There are the specification and driver installation which are listed

3. Click Start m enu and select “PenMount Utilities”; and then, a “PenMount Control Panel” pops out. 4. Select the “Standard Calibrate” tab.

5. Calibration: To adjust the display with touch panel, click “Calibration” and follow the calibrate point to do calibration; there are five

\ 4.3 Embedded O.S. The FES5105 provides the WES 7. The O.S. is supported devices which are listed below. 4.3.1 WES 7 Here are supported

CHAPTER 1 INTRODUCTION This chapter contains general information and detailed specifications of the FPC5105 Chapter 1 includes

1.2 Specifications 1.2.1 M ain CPU Board  CPU  AtomT M N2600 1.6GHz processor onboard  System Chipset  NM10 Express  BIOS

1.2.3 System Specification  10.4” TFT LCD  Heat Dispensing Design  Disk drive housing:  One 2.5” SATA drive  Net Weight  1.8

1.3 D imensions This diagram shows you dim ensions and outlines of the FPC5105.