Acnodes FES 2213 Manual do Utilizador

FES2213 Fanless Embedded System User Manual FES2213: Fanless Embedded System Atom N2600 Dual Core 1.6GHz Processor

1-5 Front I/O Front Panel Top & Bottom Panel

Chapter 2: Pin Definition & Jumper Settings 2-1 Front Panel Pin Definition 1. Power Switch 2. LAN port 3. Two RS-232 ports (COM1

2-3 Internal Pin Definition & Ju mper Settings 2-3.1 Main Board Top View 2-3.2 Main Board Bottom V iew

2-3.3 Main Board Pin Definition 1. Battery Connector [refer to BH1] MIO-2261 supports Lithium 3V/210 mAH CR2 032 battery with w ire

3. DDRIII SODIM M Socket [refer to CN 3] One 204-pin/ H9.2 mm DDRIUII DIMM socket supports DDR3 800 MHz (N26 00)/ 106 6 MHz (N2800 ) up to 4GB.

10. COM Port Connectors [refe r to CN11] MIO-226 1 provides 2 x RS-232 serial ports in 10* 2pi n pin header. It provides connections for serial

2-3.4 Jum per Settings 1. LCD Power/ Auto Power ON [refer to J1] Setting Function ( 1-2) ＋5V (3-4) (default) ＋3.3 V (5-6) (default) Auto Pow

5 . GPIO [refer to CN4] PIN PIN Name 1 ＋5V 2 GPIO4 3 GPIO0 4 GPIO5 5 GPIO1 6 GPIO6 7 GPIO2 8 GPIO7 9 GPIO3 10 GND 6 . VGA [refer to CN5 ]

7 . mSATA [refer to CN 6] PIN PIN Name PIN PIN Name 1 NC 27 GND 2 ＋3.3 V 28 ＋1.5V 3 NC 29 GND 4 GN A 30 SMB_CLK 5 NC 31 A－ 6 ＋1.5 V 32 SMB_DAT 7

PIN PIN Name 1 GND 2 TX＋ 3 TX－ 4 GND 5 RX－ 6 RX＋ 7 GND 8 . SATA [re fer to CN7 ] 9 . Mini PCIe [refer to CN 8] PIN PIN Name P

Copyright This publi cati on c ontains inform ation that is prot ected by copyright. N o part of it m ay be reproduced i n any form or by a

1 0. External USB [refer to CN9] PIN PIN Name 1 ＋5V 2 D－ 3 D＋ 4 GND 1 1. Internal USB [refer to CN10] PIN PIN Name 1 ＋5V 2 ＋5V 3 A_D－ 4 B_

PIN PIN N ame PIN PIN Name 1 DCD1# 11 DCD2# 2 DSR1# 12 DSR2# 3 RXD1 13 RXD2 4 RTS1 # 14 RTS2# 5 TXD1 15 TXD2 6 CTS1# 16 CTS2# 7 DTR1# 17 DTR2# 8 RI

1 4. Front Panel [refer to CN 13] PIN PIN N ame 1 Power Button P in1 2 Power LED＋ 3 Power/ Reset Button P in2 4 HDD LED ＋ 5 Reset Button Pin1 6

1 6. HD Audio [refer to CN15] PIN PIN N ame 1 LOUTR 2 LINR 3 GND 4 GND 5 LOUTL 6 LINL 7 NC 8 NC 9 NC 10 NC 1 7. MIOe [refer to CN16 ]

1 8. Inve rter Power/ Internal SATA Power [refer to CN 17] PIN PIN N ame 1 ＋12V 2 GND 3 ENABKL 4 VBR 5 ＋5V 1 9. 24 bits LVDS Panel [refer to C

Chapter 3: BIOS Se tup 3-1 Introduction AMIBIOS has been integrated into m any motherboards for ove r a decade. With the AMIBIOS Setup progr

3-2 Entering BIOS Turn on the computer and then press < F2> or <DEL> to enter Setup menu. 3-2.1 Main Setup When user fi rst ente

3-2.2 Advanced BIOS Features Setup Select the Advanced tab from the MIO -520 setup screen to enter the Advanced BIOS Setup screen. Use rs can sel

3 -2.2.1 Advanced BIOS Update V1.3 This item al lows users to flash BIOS. 3 -2.2.2 ACPI Settings  Enable ACPI Auto Configuration This item al

FES2213 Fanless Embedded System Safety Measures To avoid dam age to the system : • Use the correct A C input vol tage range to reduce the ris

3-2.2.3 TPM Configuration  TPM Support Di sabl e/ Enable TPM if available.

3-2.2.4 CPU Configuration  Hyper Threading Technology This item allows users to enable or disable Intel Hyper Threading technology.  Exe

3-2.2.5 SATA Configuration  SATA Controller(s) This item allows users to enable or disable the SATA controller( s).  SATA Mode Selection T

3-2.2.6 Inte l Fast Flash Standby  IFFS Support This item allows users to enable or disable iFFs.

3 -2.2.7 USB Configuration  Legacy USB Support Enabl e the support for legacy USB. Auto option di sables legacy support if no USB devices ar

3 -2.2.8 Super IO Configuration  Serial Port 1 Configuration This item al lows users to configure serial port 1.  Serial Port 2 Configurat

3 -2.2.9 H/W Monitor Configuration This page di splay all inform ation about system Temperature/ Voltage/ Current. 3 -2.2.10 AOAC Configuration

3-2.2.1 1 PPM Configuration  EIST This item allows users to enable or disabled Intel SpeedStep functi on.  CPU C state Report This item all

3-2.3 Chipset Select the Chipset tab from the M IO-2661 setup screen to enter the Chipset BIO S Setup screen. You can display a Chipset BIOS Setup

3 -2.3.1 Host Bridge / Intel IGD Configuration  Auto Disable IGD This item al lows users to auto disable IGD upon ex ternal GFX detected. 

FES2213 Fanless Embedded System Table of Contents Copyright ... ...

3-2.3.2 South Bridge  PCI Expr ess Root Port 0/1/2 This item allows users to configure P CIe port 0/1/2 settings.  DMI Link ASPM Control

 Azalia Controller Enabl es or disables the azalea control le r.  Select USB Mode Sele ct U SB mode by controllers or ports.  SMBus Cont

3-2.4 Boot Settings  Setup Prompt T imeout This i tem al lows users to select the num ber of seconds to wait for setup activation key.  B

3-2.5 Security Setup Select Security Setup from the MIO-2261 Setup main BIOS setup m enu. All Security Setup options, such as passw ord pro

3-2.6 Save & Exit 3-2.6.1 Save Changes and Exit When users have completed system configuration, select this option to save changes, exit B

3 -2.6.5 Save Changes When users have compl eted system configuration, select this option to save changes, without exiting the BIOS setup menu. 3

Cha pter 4: Software Support 4 -1. Software Application s 4-1.1 The GP IO Application General purpose Input/ Output i s a flexible parallel i

4-1.6 The Hardware Monitor Application The hardware monitor ( abbreviated as HWM) is a system he alth supervision capabili ty achieved by placing

4-2. Installation Guide 4-2.1 GP IO When the appl ication is executed, it wil l display GPIO inform ation i n the GP IO IN FORMATION group

 Test Write Single Output Pi n - Click the radio button-Single-P in. - Key in the pin numbers you want to write. Pin numbers start from “0”. -

FES2213 Fanless Embedded System Chapter 1: Introduction 1-1 Overv iew Acnodes’ FE S2213 is the latest released model with outstanding siz

 Write a byte - Key in the sl ave device address in Salve address fie ld. - Key in the regi ster offset in Register Offset field. - Key in the de

- Cli ck the radio button-Access a byte. - Key in the salve devi ce address in the Sal ve address field. - Key in the register offset i n the Registe

4-2.4 Display Control When the appl ication is executed, it wil l display two blocks of VGA control functions. The application can turn

4-2.5 Watchdog Timer When the appl ication is executed, it wil l display watchdog information in the WATCHDOG INFORMATION group box. I

4-2.6 Hardware Monitor When the Monitor application is executed by clicking the button, hardware monitori ng data val ues w ill be di splay

APPENDIX A Watchdog Timer Sample Code Watchdog function: The SCH3114 Runtime base I/O address is 6 00h Setting WatchDog time val ue l ocati

;66H ;WDT ti mer time-out value ;bit[7:0 ]=0~255 ;================ ===== ======================== ===== ======================= mov dx,SCH3114_IO +

GPIO Sample Code The SCH31 14 Runtim e base I/O address is 600h .model small .486p .stack2 56 .data SCH3114_IO EQU 6 00h .code org 100h .STARTup

1-2 Product Sp ecification P rocessor & Chipset  Sup port Atom N2600 Dual-core 1.6 GHz Processo r  NM10 Sou th Brid ge Chip set Graphic Engin

RS-232 Supports  2 DB-9 for RS-232 with auto -flow control Each por t support 16 Byte FI FO, optional 5V DC outpu t Front Panel Extend I/O Ports 

1-3 System Block Diagram FES 2213

1-4 Mechanical Diagrams FES 2213