Acnodes FES 8730 Manual do Utilizador

FES 8730 Fanless Embedded System 14628 Central Ave, Chino, CA91710 tel:909.597.7588, fax:909.597.1939 © Copyright 2013 Acnodes, Inc. All rights reserv

1.1 General Description The FES8730 is an embedded system that supports onboard Core™ i7-2610UE (2.4GHZ), i3-2340UE(1.3GHz) or Celer

1.2 System Specifications 1.2.1 CPU  CPU  Core™ i7-2610UE (2.4GHZ)  Core™ i3-2340UE(1.3GHz)  Celeron® B810(1.6GHz)  Chipset

 Storage Temperature -20℃ ~ 80℃ (-4 ºF ~ 176ºF)  Humidity 10% ~ 90% (non-condensation)  Vibration Endurance 3Grm w/ CFast and SS

1.3 Dimensions The following diagrams show you dimensions and outlines of the FES8730. 1.3.1 System Dimension

1.3.2 Wall mount Bracket Dimension

1.4 I/O Outlets The following figures show you I/O outlets on front view of the FES8730.  Front View drawing Power Reset LAN2 LAN1

1.5 Packing List The package bundled with your FES8730 should contain the following items:  FES8730 System Unit x 1  FES8730 Quick Instal

1.6 Model List FES8730-2610UE-DC Fanless Embedded System with Intel Core i7-2610 2.4G Proecssor, DVI-I, DisplayPort*2, GbE

CHAPTER 2 HARDWARE INSTALLATION The FES8730 is convenient for your various hardware configurations, such as HDD (Hard Disk Drive),

Disclaimers This manual has been carefully checked and believed to contain accurate information. Acnodes Corp. assumes no responsi

2.1 Installing the 2.5” SATA Device Step 1 Turn off the system, and unplug the power cord. Step 2 Turn the system upside down to locate scre

Step 4 Assembly the HDD bracket together with the 2.5” SATA device Step 5 Slide HDD/SSD bracket module into

Step 6 Fasten screws of HDD bracket Step 7 Close the cover to the chassis, and fasten all screws.

2.2 Installing the CFast™ Step 1 Turn off the system, and unplug the power cord. Step 2 Turn the system to the side with CFast cover. Step

Step 5 Close the cover to the chassis, and fasten all screws.

2.3 Installing the Express Mini Card Step 1 Turn off the system, and unplug the power cord. Step 2 Turn the system upside down to locate

Step 4 Slide Mini card into Mini Card slot with caution and Fasten screw of Express Mini Card. Step 5 Assembly the Top Cover back and faste

CHAPTER 3 Jumper Setting & Connectors FES8730 is a “jumperless” system. Due to all the hardware settings are done via software or fir

3.1 SBC layout Bottom Side NOTE: We strongly recommended that you should not modify any unmentioned jumper setting without Acn

Pin Signal 1 DC + 2 GND 3 DC - 3.2 Connectors Connectors connect the system with other parts/devices. Loose or improper co

Safety Precautions Before getting started, please read the following important safety precautions. 1. The FES8730 does not come equipped with an

3.2.2 Isolated Digital Input Connector The system is equipped with an 8-channel digital Input connector that meets requirements for a system

3.2.3 Isolated Digital Output Connector The system is equipped with an 8-channel digital output connector that meets requirements for a sy

3.2.4 DVI-I Connector The system comes with a high rise DVI-I (Digital Video Interface – Integrated) interface providing transmission of fas

3.2.5 DisplayPort Connector DisplayPort interface is also called DP port. Pin Signal 1 DPB_LANE0 2 GND 3 DPB_LANE0# 4 DPB_LANE1 5 GND 6

3.2.7 COM1~COM2 Serial Port Connector The system has eight serial ports. COM1~COM2 are RS-232/422/485 ports. Please refer to Ch

3.2.8 COM3~COM4 Serial Port Connector The system has eight serial ports. COM3~COM4 are RS-232 ports. Pin Description 1 ISO_GND3

Pin Signal USB Port 0 Pin Signal USB Port 1 1 USB_VCC (+5V level standby power) 10 USB_VCC (+5V level standby power) 2 USB_Data2- 11 USB

3.2.12 Audio Connector These two audio jacks ideal are for Audio Mic-In and Audio Line-out. Pin Signal 1 Line Out 2 Microphone I

3.2.15 Reset Button The Reset button can allow users to reset FES8730. Function Description On Reset system Off Keep system status

3.2.17 CFast™ Socket The system is equipped with a CFast™ socket on the bottom side to support a CFast™ card which is

Classification 1. Degree of production against electric shock : not classified 2. Degree of protection against the ingress of water : IP40 3.

3.2.18 Express Mini Card Slot PCI Express Mini Card connector supports a PCI Express x1 link and a USB 2.0 link. A PCI Express Mini Card

CHAPTER 4 AMI BIOS SETUP UTILITY The AMI BIOS provides users with a built-in setup program to modify basic system configuration.

Hot Keys Description  Left/Right The Left and Right <Arrow> keys allow you to select a setup screen.  Up/Down The Up and Down <Arr

4.3 Main Menu When you first enter the setup utility, you will enter the Main setup screen. You can always return to the Main setup screen by

4.4 Advanced Menu  Launch PXE OpROM Use this item to enable or disable the boot ROM function of the onboard LAN chip when the system boots

 ACPI Settings You can use this screen to select options for the ACPI configuration, and change the value of the selected option. A descriptio

 CPU Configuration This screen shows the CPU Configuration, and you can change the value of the selected option. Intel Virtualization Techn

 H/W Monitor This screen monitors hardware health. This screen displays the temperature of system and CPU, cooling fan speed in RPM and

 NCT6106D Second Super IO Configuration You can use this screen to select options for the Super IO Configuration, and change the value of the se

 Serial Port 1 Configuration Serial Port Use this item to enable or disable serial port 1. The optimal setting for base I/O a

General Cleaning Tips You may need the following precautions before you begin to clean the computer. When you clean any single part or component fo

 Serial Port 2 Configuration Serial Port Use this item to enable or disable serial port 2. The optimal setting for base I/O

 Serial Port 3 Configuration Serial Port Use this item to enable or disable serial port 3. The optimal setting for base I/O

 NCT6106D Super IO Configuration You can use this screen to select options for the Super IO Configuration, and change the value of the selecte

 Serial Port 1 Configuration Serial Port Use this item to enable or disable serial port 1. The optimal setting for base I/O a

 Serial Port 2 Configuration Serial Port Use this item to enable or disable serial port 2. The optimal setting for base I/O

 Serial Port 3 Configuration Serial Port Use this item to enable or disable serial port 3. The optimal setting for base I/O

4.5 Chipset Menu The Chipset menu allows users to change the advanced chipset settings. You can select any of the items in the left frame of

 System Agent (SA) Configuration This screen allows users to configure System Agent (SA) parameters. For items marked with “”, please press &

 Graphics Configuration LCD Control This item allows you to select graphic output control options. Please press <Enter> to go to

Primary IGFX Boot Display Allow you to select the video device which will be activated during POST. This has no effect if external graphics

Scrap Computer Recycling If the computer equipment’s need the maintenance or are beyond repair, we strongly recommended that you sh

 Memory Configuration This screen displays memory information.

4.6 Boot Menu The Boot menu allows users to change boot options of the system.  Setup Prompt Timeout Number of seconds to wait for se

4.7 Security Menu The Security menu allows users to change the security settings for the system.  Administrator Password This item in

4.8 Save & Exit Menu The Save & Exit menu allows users to load your system configuration with optimal or fail-safe default values.

 Discard Changes Select this option to quit Setup without making any permanent changes to the system configuration. Select Discard Changes fro

Appendix A Watchdog Timer About Watchdog Timer Software stability is major issue in most application. Some embedded systems are no

How to Use Watchdog Timer Begin Begin Next Next Enable and Initialize Watchdog Timer Enable and Initialize Watchdog Timer Ne

Assembler Sample Program ;Enable WDT: Mov dx,4Eh Mov al,87h ;Un-lock super I/O out dx,al out dx,al ;Select Logic device: mov dx,4Eh mov al,07h

;Disable WDT: mov dx,4Eh mov al,30h out dx,al mov dx,4Fh mov al,00h ;Can be disable at ant time out dx,al Note: When N’s value is 00h, the

Appendix B Programmable LED About Programmable LED FES8730 supports two programmable LED which allows user to program the LED status. It ca

Table of Contents Disclaimers ... ii

Assembly sample Code: Set functionality: ;Start set LED Output program: mov dx,2Eh ;Un-lock super I/O mov al,87h out dx,al out d

Note1: The N has 8 bits. Only bits 4,5 are programmable. " 1" means that the bit is programmed to input. " 0" means t

CHAPTER 4 AMI BIOS SETUP UTILITY ..... 33 4.1 Starting ...

CHAPTER 1 INTRODUCTION This chapter contains general information and detailed specifications of the FES8730. The Chapter 1 includes the followi