Acnodes FPC 8759 Manual do Utilizador

FPC 875X Fanless Panel PC User Manual FPC875X: 10.1/15.6/18.5/21.5” Fanless Touch Panel PC with Atom D2550 1.86GHz /Pentium G630T 2.3GHz Processor

2-3. I/O view m C48 Motherboard m

170mm 2-4. Dimensions 2-4-1. 10.1" System 263mm 38mm

284mm 328mm 2-4-3. 18.5" System 464mm 2-4-4. 21.5" System 48mm 536mm 48mm

3. System Assembly 3-1. Open the Chassis Cover The motherboard and RAM module can be replaced by opening the chassis cover, which is loca

3-2. RAM Module Replacement To remove and replace the RAM module, please open the chassis cover firstly as steps dscribed in chapter 3-1.

Installing a RAM moudle 3. Slide the memory module into the memory slot and press down until the ejector clips snaps in place.

3. Attach the HDD to the HDD tray and slide it into the slot until it snaps in place. * Please note the top of the HDD should be on the

4. Peripheral Installation 4-1. MSR Installation To install MSR, please open the cable cover firstly as steps described in cha

4-2. Stand Installation 1. Place the system face down. Make sure not to scrath the screen. 2. Attach the stand to the back of the system.

Pin Signal 1 GND 2 DOUT bit0 3 DIN bit0 4 12V / 19V 5 DOUT bit1 6 GND 4-3. Cash Drawer Installation You can install a cash drawer through the

Copyright 2013 All Rights Reserved The information contained in this document is subject to change without notice. We make no warranty of any kind

Bit 7: Reserved Bit 6: Cash Drawer “DIN bit0” pin input status. = 1: the Cash Drawer closed or no Cash Drawer = 0: the Cash Drawer opened Bit 5: Res

5. Specification Model Name FPC8755 FPC8758 FPC8759 Mainboard C48 CPU Atom D2550 processor 1.86GHz Chipset NM10 Sy

Environment EMC & Safety FCC Class A, CE, LVD Operating Temperature 0°C ~ 35°C (32°F ~ 95°F) Storage Temperature -20° ~ 60°C (-4°F ~ 140°F) Op

Model Name FPC8752 Mainboard C56 CPU

Environment EMC & Safety FCC /CE Class A/ LVD / EN 60601-1-2/ UL Operating Temperature 0°C ~ 35°C ( 32°F ~ 95°F ) Storage Temperature -20°C ~

2 4 6 8 10 12 141 618 20 22 24 26 28 30 B D C E F G H J K L M N P R T V U Y W AA AB AC AD AE AF AHAG AJ AK AL AJ AG A

DDR3_A2

6-1-2. Connectors & Functions Connector Function CN1 Power Button Connector CN3 Printer Port Reset CN4 Printer Port CN5/8 HDD Power CN11 C

6-1-3. Jumper & BIOS/Utility Setting COM2 RS232/485/422 Setting Function JP5 JP4 ▲RS232 1 3 5 7 9 2 4 6 8 10 1 3 5

4. To switch on the power, select "Power". Please save the change before exiting BIOS so as to go for physical jumper adjustment.

CE MARK This device complies with the requirements of the EEC directive 2004/108/EC with regard to “Electromagnetic compatibility” and 2006/95/

Cash Drawer Power Setting Function JP19 +19V 1 3 2 4 ▲+12V 1 3 2 4 Power Mode Setting Function JP9 ▲ATX Power 1 2 AT Power 1 2

CMOS Operation Mode CMOS Reset To clear the CMOS, 1. Remove the power cable from the system. 2. Open the system, and set the ‘CMOS Operation jump

LCD ID Setting Several configurations are applied to different sizes of panel. Please refer to the followings to complete relevant settings. R

4. To switch on the power, select "+12V". Please save the change before exiting BIOS to avoid data lost. LCD Brigh

2 15 2 6-2. C56 Motherboard 6-2-1. Motherboard Layout CN11 RJ11_1 USB1 JP9 CN12 CN8 SATA2 CN6 USB2 RJ45_1 SATA1 SATA4 CN13 CN

6-2-2. Connectors & Functions Connector Function CN1 LVDS Inverter Connector CN2 System FAN Connector CN3 LVDS Connector CN4 Power LED Connec

6-2-3. Jumper Setting Cash Drawer Power Setting Function JP9 ▲ +19V 1 3 2 4 +12V 1 3 2 4 Inverter Selection Function JP1 ▲ CCFL

4. To enable the power, select COM2 , COM3 or COM4 Power setting and press <Enter>. Select Power and press <Enter>. Save the change b

LCD ID Setting Panel# Resolution LVDS Output Interface JP3 Bits Channel 1 800 x 600 18 Single LVDS Panel 1 3 5 7 9 2 4 6 8

Intel Graphics Driver Setting 1. Right click Desktop. Find "Graphics Properties" and enter the manu. 2. Make sure th

LEGISLATION AND WEEE SYMBOL 2002/96/EC Waste Electrical and Electronic Equipment Directive on the treatment, collection, recycling and disposal

6-3. IdeaCom Touch Driver Installation If your system is installing with the POS touch driver, please follow the below steps to remove the

5. Click <Next> 6. Click <Finish> to exit. 7. Click <OK> to reboot your system to complete t

Please follow the below steps to install the IdeaCom touch driver. Driver Location Folder/File Fille Description <CD>:\Common\IdeaCom_T

4. Click <Next> to proceed the installation. 5. Click <Finish> to restart your system.

6-3-1. Gesture Setup example for WinXP 1. Open <IdeaCom Touch Screen Manager> utility. (You can click IdeaCom Logo or select <S

3-1. Check <Previous Image> hot key 3-2. Select <Hot Keys>, then set <Left Arrow> hot key

5-1. Check <Zoom Out> hot key 5-2. Select <Hot Keys>, then set <Down Arrow> hot key 6-1.

7-1. Check <Rotate Counterclockwise> hot key 7-2. a. Select <Hot Keys>, then set <Rotate Counterclockwise>

6-3.2. Gesture Setup example for Win7 1. Open <IdeaCom Touch Screen Manager> utility. (You can click IdeaCom Logo or select <Star

3-1. Check <Previous> hot key 3-2. Select <Hot Keys>, then set <Left Arrow> hot key 4-1. C

Table of Contents 1. Packing List... 1 1-1. Standard Items ...

5-1. Check <Rotate Counterclockwise> hot key 5-2. Select <Hot Keys>, then set <Rotate Counterclockwise> hot k

8. Key in <Profile Name> to save, then click <OK> 9. Select <Apply> and clicck. Finally click <Yes> to save

Appendix: Drivers Installation The shipping package includes a Driver CD in which you can find every individual driver and utility that enables you

5. Specification ... 15 6. Jumper Setting... 20 6-1. C48 Motherboard...

1. Packing List 1-1. Standard Items a. b. c. d. e. f. g. a. System b. Power adapter c. Driver bank d. Power cord e. User m

1-2. Optional Items MSR

2. System View 2-1. Front & Side View 2 3 4 1 1. Touch screen 2. Built-in web cam 3. Ventilation 4. MSR cable